Recommended
Likes
Comments
Share
***UPDATE 03/26/25*** Gave each plant 350ml of dechlorinated tap water at a PH of 6.0 Rearranged the plants so they are directly underneath the bars of light above! The Strawberry Dawg Pie is looking much better at the start of week 3, hoping no more issues with water & light! Temps & RH have been good so far today, RH is on the climb to 70%! ***UPDATE 03/27/25*** Plants responded fairly well to yesterdays watering! Little bit of droop but should perk back up over the next 12 hours or so, 350ml next feed will be best vs jumping right to 500ml, am gonna wait until they have completely dried out before feeding again! Will keep an eye on all 4 plants over the next couple of days, want to remove large fan leaves prior to mainlining! Temps & RH have been pretty good so far today as well! ***UPDATE 03/28/25*** Not much needed to be done today, will probably defoliate in the next day or two & begin mainlining! Temps & RH have been good so far today! ***UPDATE 03/29/25*** Pots are still saturated & I will not have to water for another day or two, some clawing on new growth even at 350ml per plant! Should be able to defoliate & begin LST tomorrow afternoon! Temps & RH have been good so far today, RH will slowly climb back up to 70% over the next hour or two now that the door to the tent is closed! ***UPDATE 03/30/25*** Nothing needs to be done today, will be feeding tomoroow afternoon alongside defoliation & LST! ***UPDATE 03/31/25*** Gave each plant 250ml of dechlorinated tap water mixed with nutrients listed above at a PH of 6.2 All 4 plants have been clawing so I decided to dial it back a bit water wise for now Defoliated, topped & have started LST! RH has been good today but temps have been quite low! ***UPDATE 04/01/25*** Plants responded well to yesterdays feed! Still a bit of clawing but pots are drying up much quicker at 250ml will probably need to water again tomorrow! Some more LST today, had to pinch to soften tissue in order to get the plants anchored down properly! Noticed a couple hairs on the Gravely Ghost, am hoping I still got a bit of time to train & top before flower! RO system showed up today! Got that mounted to a cutting board with L brackets for feet so I can move it around! 5 Gal bucket is currently filling up but is quite a slow process.. Gonna double check with other people who own the unit to see if it's is a normal speed! (Aquatic Life RO Buddie 4-Stage Reverse Osmosis, picture & video above) Checked TDS & is looking like 300ppm ish straight from the tap, RO filtered water is sitting at 4ppm which is good! Temps & Humidity have been pretty good today!
Likes
5
Share
@N1gh7M4r3
Follow
Durante esta semana aplicamos aplical Nos fue bastante bien… Hicimos clones, espero salga alguno.
Likes
4
Share
@Kannamar
Follow
25/04/2023 Day 69 I cut the "twins" and finally discovered the inside of the DWC MyPot. I took lots of pics so you can see the unexpected plant of the seed that I lost in the clay and then germinated anyway and found an awkward path to the surface through a tiny hole! Unbelievable! I also found that the watering tube from the pump had moved during manipulation, don't know for how long it has been pressed between the upper and lower parts on the DWC. Pretty sure for that final plants had received less or no feeding solution, and the use of Clean might not have been efficient. I guess it's also the reason why I found the white (?) on the top of the clay, salts and something else, because of lack of watering. Will come back in 3 weeks, will be dry and then I'll can trim and weight. And smoke, yeah! Not expecting much and could be hard to smoke if the cleaning was not efficient. Anyway, the next one will be better!
Likes
6
Share
@KivzBudz
Follow
Overall I’m very happy to end my first run like this. I think I made a pretty decent job and I can’t wait to try the finished product after curing. Happy growing everyone! 🍀🌱
Likes
22
Share
Seed to harvest day 67 Sticky buds Fruity smell Good strees performance Total Used power 400w
Likes
18
Share
PURPLE KUSH / KANNABIA SEEDS WEEK #20 OVERALL WEEK #8 FLOWER This week she's starting to get some aroma to her and her buds are getting frosty she's got about 2 weeks left before harvest she's got a nice buds structure going on!! Stay Growing!! Thank you for stopping by and taking a look it's much appreciated!! THANK YOU KANNABIA!!! KANNABIA.COM / PURPLE KUSH 💜
Likes
6
Share
@Ninjabuds
Follow
Gorilla cookies is a beast of a plant it can easily fill up a 4x4 with one plant if done right. Really thick white tricombs strong smells big colas. What else can you ask for a good plant all around
Likes
107
Share
💩Holy Crap Growmies We Are Back💩 Entire grow has been stunted by the soil/medium Code Name FBT2309 Well growmies we are at 49 days in and everything is going as good as possible 👌 👉 Well folks shes been a busy girl , making a ton of bud , just hope she chunks up 👌 Lights being readjusted and chart updated .........👍rain water to be used entire growth👈 👉I used NutriNPK for nutrients for my grows and welcome anyone to give them a try .👈 👉 www.nutrinpk.com 👈 NutriNPK Cal MAG 14-0-14 NutriNPK Grow 28-14-14 NutriNPK Bloom 8-20-30 NutriNPK Bloom Booster 0-52-34 I GOT MULTIPLE DIARIES ON THE GO 😱 please check them out 😎 👉THANKS FOR TAKING THE TIME TO GO OVER MY DIARIES 👈
Likes
2
Share
Going into week 4. After. A transplant and at the end of week 3 they have seemed to recovered and are doing great. I’ve noticed that they “pray” towards the light so they seem to be happy. Using 1ml of cal mag. When I water. Ph. 6.1 -6.3 of 90%RO 10% tap. Added the second mars hydro on day 25. Update last day of week 4 day 28. The ladies ain't looking too happy. Being hit by I imagine Cal mag deficiency. Even tho I was expecting it because of the RO water. It seems I didn't add the Cal mag fast enough. Hopefully.the 2ml/L or Cal mag. Will fix it. Last watered 250ml each of PH 6.2 water on 8/28
Processing
Likes
11
Share
This poor, sad little girl. I feel bad for neglecting her earlier on. But hopefully she will live up to her namesake and persevere! (I guess it is a little messed up that the strain is Widow Remedy and I killed both of her husbands😕) Anyway... So bugs suck, and I sprayed with some neem oil and put out a sticky trap. Fertilized with some of the Coast of Maine and watered it in with some lime water. Heat wave is moving through right now, I hope she likes it hot😎 Forgive my slurred speech in the video, it's been a long week and my brain is addled😜
Likes
17
Share
@leliantu
Follow
Hola. No había actualizado estas plantas, aquí va. Semana 18. Las plantas ya llevan alrededor de 13 días en riego solo con Flawless Finish, las flores pegaron una ultima engordada y ya están madurando, ambas variedades han adoptado tonalidades muy linda.
Likes
6
Share
Battling the start of powder mildew. Just need to hold it off a bit longer. Neighbours are noticing a smell haha.
Likes
3
Share
@Bluemels
Follow
Tag 34: Schon wieder kriegen meine Pflanzen helle Blätter! Ich halte mich an das Düngeshema von Biobizz und stelle den ph Wert ein.
Likes
15
Share
@Messypies
Follow
Lovely growth on the buds this week. Struggling to smell at the moment due to my filter but once out of the tent it is smelling beautiful
Processing
Likes
38
Share
February 16, 2021 (Week 6, Day 43): Very nice canopies beginning to develop now. Growth sites are apparent and growing vertically. Had to slow Unknown 1 down just a little bit because it's outgrowing the other plants; brought branches down level with other canopies. I watered today with 4 liters per plant + 2ml/l pH Perfect Grow + 3ml/l pH Perfect Bloom + 1ml/l Cal-Mag Plus at 5.6 pH. Runoff sitting at a perfect 6.5pH and 900ppm. Loosened all remaining LST ties to promote upward growth. It's officially wall-to-wall leaves in here now. I hope there's lots of great growth this week so we can switch to flower soon! Turned down humidity again. Now averaging 55% rH and 74℉. Please feel free to leave any feedback! Since this is my first grow I want to make sure everything is looking right! Happy growing! 👻 February 17, 2021 (Week 6, Day 44): Saw between .5-.75" vertical growth over the last 24-hours. Canopy is coming along nicely. Everything is growing very evenly - I only had to adjust one branch to keep it in-line with the others. Hopefully they'll continue to grow even with each other. Medium is still very moist after watering yesterday. Gelato 1 seems to be drinking a bit more than the others, but I'll keep watering on the same schedule to promote adequate drying of the root-zone. Averaging 55% rH and 77℉. No other news today. February 18, 2021 (Week 6, Day 45): Another half inch of growth overnight. These ladies are trucking along and flowering is just around the corner. With this growth I'll definitely be switching to flower on day 50. Medium is still moist, lightly tilled topsoil. LST is holding down the main branches well while allowing a bit of stretch. Hopefully this progress keeps up! Averaging 55% rH and 74℉. February 19, 2021 (Week 6, Day 46): Growth on growth on growth. Plants tacked on between .75-1" of new growth overnight. Soil was bone dry this morning and pots were super light. Watered with 4l per plant + 3.5ml/l pH Perfect Bloom + 2ml/l pH Perfect Grow + 1ml/l Cal-Mag Plus @ 5.8 pH. Runoff sitting at 6.6 pH. The plants are starting to drink a lot and I barely got any runoff. I will add a quarter teaspoon of my Humboldt Nutrients Big Up flower powder to kick-start the plants and switch them to flower. I took four fan leaves off Unknown 1 as they weren't getting any light. Took all remaining LST ties off of Unknown 2 as it is lagging behind the others (as usual). Averaging 55% rH and 74℉. February 20, 2021 (Week 6, Day 47): Manifolding is coming along nicely. Defoliated bottom-most node on each growth stem on each plant. Soil is only moist after watering yesterday - these plants are getting thirsty as hell. Tilled half inch of top soil. Everything looks great today. The anticipation to switch to flower in a few days is killing me! Happy Saturday everyone! Averaging 55% rH and 75℉. February 21, 2021 (Week 6, Day 48): Another inch of growth overnight. We are up to 12" in total height now. Was aiming for about ~16", but since this is my first grow I am not trying to be exact, I just want to make sure these things fit in my tent after the flowering stretch. Everything is looking great for the switch in two days. Soil is slightly moist - tilled top half inch of soil. Adjusted a couple of branches on Unknown 1 to keep growth level. Plants are looking perfectly healthy! Gelato 1 is spitting out pistils and pre-flowers like she just can't wait to start. Smelling really creamy and sweet. Averaging 55% rH and 74℉. Nothing else for today. 😺 February 22, 2021 (Week 6, Day 49): It's the last day of veg! Plants will sleep at 8:00pm and wake up at 8:00am from now until harvest. Medium is quite dry but I will water tomorrow morning with my first batch of flowering nutrients. I'll use Advanced Nutrients Big Bud and Botanicare Sweet Raw for the first 4-5 weeks, and then I'll switch over to Humboldt Nutrients Big Up flower powder for the last several weeks to finish it off. I'll feed just a tiny bit of the finisher tomorrow to give the plants a potassium/phosphorus boost to induce flowering. Really excited for the next step in this process! Now I am trying to finish up my plan for drying and curing so I don't ruin all this work in the last week! Averaging 55% rH and 74℉. Stay tuned - the fun is just beginning! 👻
Likes
9
Share
All the photos are in the 8x8 now just a few autos in here now FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com www.marshydroled.ca PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress Instagram: @marshydropenny Thanks for taking the time to read and check out my diary🤜🤛 TS3000 FEATURES: WIDEBAND SUNLIGHT FULL SPECTRUM LED GROW, Infinite close to natural sun light, suit for all plants whole stages indoor growing, rapid plant response from seed to flower, achieve maximum quality and quantity, much better than traditional HPS grow systems. HIGH REFLECTIVE & NOISE FREE-Fanless LIGHT BOARDS design will make your growing life easy and quiet, quickly heat dispersing material aluminum reducing light lost to aisles and walls, increase the light intensity up to 20%, allowing your plants receive more energy and without burning your plants for maximum headroom. HIGH EFFICIENCY ENERGY SAVING PLANT LIGHT, high-power NEW LED grow, Compares to traditional 3000 watt HPS lamp and other brand led grow light while only 450 watts true output with 1016 LEDs, more scientifically and energy-efficient! Perfect for 5' x 5' veg stage, 4' x 4' bloom stage, higher intensity in a MARS HYDRO grow tent, reflective area, or by crossing over using multiple TS3000. BOOM YIELD LARGE GROW LIGHT, NEWEST SMD LED technology provide highest PAR/LUMEN output(1095.6umol/), makes you get 30% higher yield compare OLD led lights, can get max yield at 2.5g/watt, less pay but get more yield, bring a amazing grow trip to any home grower as it beams huge amounts of light energy to plants below. COMMERCIAL LED GROW LIGHT, Updated easy dimming & daisy chain function, main light controlled, especially come with two waterproof and dimmable Mean Well Drivers, auto sensing power supply works on both 120VAC and 240VAC and 277VAC, suit for Large Rooms and Commercial Setups. Low Energy-Consuming LED Grow Light: Consuming 300w and also mounted with 1016 chips, TS3000 has the ability to replace a 450w HPS light while reducing 40% power intake. High Efficiency LED Grow Light: With overall light output PPF 343umol/S as well as amazing PPE 2.3 umol/j, it's 50% even more photon efficient and can assure a 30% more return than the old HPS/MH lights. Patent Highly-Reflective Hood Shape: The reflector design on TS3000 is patented, which can effectively gather the light dispersed in all directions to enhance its light intensity as well as assist plants in absorbing more light. Full Spectrum Plants Favorite Spectra: By the unique mix of spectra that makes most light in the 400-700nm waveband, incredibly conducive to plant photosynthesis. Adequate IR(730-740nm) is additionally consisted of in the range to generate larger buds. Dimming And Daisy Chain Feature Available: Upon an independent dimming button on the external driver, backing 0-100% settings adaptation and up to 30 LEDs daisy-chained in a group, it supplies different light levels for various plant stages meanwhile saving energy. Safety Certifications And Service Warranty: CE, ETL, RoHS, UKCA security certifications accepted, 50,000 hours durability, 5-year service warranty, and local after-sales repair 5x5 GROW TENT: LOCK ALL LIGHT INSIDE MARS HYDRO Indoor Grow Tent interior is made of diamond mylar which is highly reflective. (Other brand's mylar and reflective rate is as low as 50%, won't provide efficient light. )MARS HYDRO 1680D canvas, being double stitched, it is tear proof and has perfect light locking. Mars Hydro's grow tent keeps 100% lighting beams inside and helps your plant absorb more lights. EXTRA-THICK --No light leaks or rips at all DURABILITY GROW TENT Stable metal corner adapters and poles are the trustful supporters of the tent, standing sturdy, neither rusting nor paint-falling, quick easy tool-free installation. Mars Hydro's heavy-duty metal zippers, with double layer black lining, are the best on the market which create a light-proof seal EASY OBSERVATION FOR YOUR PLANTS. Special observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing plants. The observation window also serves to dissipate heat and ventilate air AUTOMATIC 6 INCH EXHAUST FAN KIT W/ CONTROLLER: Mars Hydro 6'' Inline Fan uses a mixed-flow design to maintain peak performance in a high static pressure environment. GROW TENT FAN: MARS HYDRO inline fans are designed to ventilate hydroponic grow rooms, transfer heating/cooling, cool AV closets, and exhaust odors. EFFECTIVE VENTILATION: Variable speed controller for easy fan speed adjustment. Optimal ventilation for your planting. LOW NOISE LEVEL: Durable plastic fan housing and blades for extremely low noise(32dB-A); create a truly quiet growth environment. EASY INSTALLATION: Removable duct ends with locking tabs for quick removal and easy maintenance and a cord length of 4.9 feet for hassle-free setup. This grows tent fan with a controller for easy fan speed adjustment. BASIC PARAMETERS: Ventilation exhaust fan size: 6” | Dimensions: 315mm*225mm*210mm. | Weight: 2.7. | Airflow: 402CFM | Noise: 32dB-A | Bearings: Dual Ball.