Removed a few leaves from 1st and 2nd lady which where covering some branches. 36: Some brown things in the flower. Is that normal? 1st lady is just growing in the lachuza pon granulate. it has ph 7.1 and i just watering her with pur water. maybe it will work but her developing seems to be behind 2nd lady. 37: Feeded 2nd lady with 1.5l water PH 5.8 and 2ml/l BioGrow and 2ml/l BioBloom, That cocktail had ec of 414ppm. the water had around ec of 180 ppm. I will try to optimize the mix of purified water and tap water. What should the proportion be between cal/mag? The tap water has a proportion of 7:1. 40: Feeded 2nd lady with 1.0l water PH 5.9 and 2ml/l BioGrow, 1 ml TopMax and 3ml/l BioBloom, That cocktail had ec of 580ppm. the water had around ec of 200 ppm. A few lower leaves look a very little bit turning into light green. At all she looks very healthy in my opinion. And they are really stinky 😂 The side branches grow fine. I counted 10 of them 😍 They reach nearly 30 cm. Main branch is over 40 cm I think. Need to buy a measurement think 😇 I think LST is good for dwarfs but I have to work on the technique a little bit in the future. 41: I can measure height now. 1st lady is only 28cm. 2nd lady is 38cm and side branches 28cm. 42: Same cocktail as week 40. 1.25 l

Hey now, hope everyone is having a great weekend and staying safe. Another great week for the ladies, as they are now almost halfway through flowering which is 4 weeks into flower, and the stretch has just finished. I am still feeding them silica, cal mag, and flower nutrients maxi bloom by GHE. I did start to add a PK booster last week pushing the EC up to 1.4. I also switched the Medic Grow light from V1 to the F1 Spectrum at the beginning of last week, and will be integrating the UV/IR bar into the light cycle later this week. I will run the UV/IR bar for approximately 30 minutes prior to lights off to get started. The tallest plants are the Sundae Driver and the Durban Nights at 44" and the Red Hot Cookies is the shortest plant at 40" however they all look happy and healthy and capable of easily giving up a half pound each. The 5X5 tent is starting to really fill up and they are just now starting to smell. I was out of town all weekend so I was unable to make a time lapse video but I will update next week. I did defoliate twice this week and I may do one or two more rounds before just letting them do their thing. Not much to do from here on out except make sure the reservoir is full and the PH is in the proper range. I hope everyone has a great weekend, Thanks for stopping by, Stay Safe and Blaze On!!! 💪 Website: https://medicgrow.com/ https://growdiaries.woodroom.tel/grower/medicgrowled

Utopia Haze is a rare heavily sativa dominant hybrid (90% sativa/10% indica) strain created through back crossing Brazilian Sativa strains. This tasty little bud took home 1st Place for Best Sativa in the 2008 High Times’ Cannabis Cup and for good reason – with its potent 18-22% average THC level and long lasting cerebral effects, Utopia Haze is one powerhouse smoke. The Utopia Haze high comes on soon after you finish your first toke, hitting you with a strong cerebral lift that infuses you with a sense of hazy relaxation. Type: Feminised/Photoperiod Cultivation: Indoor/Outdoor Flowering Time (days): 70-75 Indoor Yield (g): Up to 650 Feminised Outdoor Harvest Month: October Feminised Outdoor Harvest Month Week: 3rd-4th week Aroma: Citrus, Woody, Pungent, Mint Effect: Cerebral Lift, Hazy Relaxation, Sleepy Welcome Everyone to the Final Entry of my Utopia Haze Grow ! There is so much to discuss ! I have been extremely busy as of late trying to get this Harvest together, but i am happy to have it here for you now ! I Seriously under estimated the amount of time, help from others, and my own necessary skills to pull this off.. and i still kind of screwed it up lol ! But its worth noting i have never actually done this before and trying to document it during....was extremely hard. It is next to impossible to work an iPhone with rubber gloves on ! First I want to discuss everything step by step so before you jump straight into the comments on how the end product is so small in "quantity" Rest assured i am happy with its"quality"...and thats all that matters to me because Life is a journey not a destination! and i have learned so much from this grow that I couldn't be any happy even if i messed some things up :) But at the very least I hope you read through this entry in its entirety with an open mind and focus more on the process, rather than just the outcome! I ran out of Ice & i was only able to wash three times..(normally I've heard you should go sometimes 5-6 washes) Preparation is Key & things will be much better next round :) Photos 1-22 These are pretty self explanatory but for those of you just tuning in now.. this is what happens to a very happy plant when you don't have the necessary tools to monitor key components of growing cannabis.. Ph, as well as EC levels play a very key role in the outcome of your grow lol that being said I was just able to save this plant by purchasing both tools but that doesn't mean the plant didn't suffer because of the prior events.. This was a Huge reason behind me choosing to turn this harvest into what i would consider "Solventless Hash Rosin" from "Ice water extracted Bubble hash". Pictures 23 The idea here is the process of using "fresh Frozen Cannabis" this has been discussed many a time online on such sites as instagram and here on grow diaries as well.. I personally have Never tried the process so i decided to try it out and make a judgement for myself.. Video 24 The Cannabis has now been in the freezer for 72 hours making it very well frozen.. as you can tell i struggled getting it all into the 25u Screen Wash Bag. One thing of note i would do differently is i will de-stem my next batch as i also believe this played a part in the amount of plant matter that escaped through the sieves. Photo/Video's 25-28 The idea here is "ice water Seiving" & especially with the bags that I am using here that are only have screen material on the bottom portion of the bag it is very important to have spaces in-between the screens to allow the water to pass directly through the screens into the bottom bucket with the least amount of resistance.. because the hash is so extremely temperature dependant if it gets warm on the side of the bag.. it will stick there and not make it to the bottom to become use able product.. 29 You do not need to use as much Ice as i used here lol... the idea is to keep everything very cold..i certainly achieved that but at the sacrifice of using so much that i ended up grinding product and producing "contaminants" but in the end they are just plant matter that i would be smoking when i rolled up my joint either way so.. I'm not super disappointed.. But it should be noted that what you want to achieve here is a Layering effect where you have the wash bag between two small layers of ice while the "water current" washes the Trichomes away allowing them to be separated by the screens setup below :) Before Starting the machine you should allow some time (i.e.;10-12minutes pre soak to allow the product to become saturated) before the first cycle. By video 32 I have just ran out of ice lol.. Video 33-34 Here I have a tip for you.. to separate the screens that you sieve through.. cut 5 gallon buckets to stretch them across nice and tight.. it'll make scooping your Bubble that much easier ! i learned this from the many "Frenchy" videos I have watched :) Picture 35 Here in lays the problem for most people.. drying your hash without loosing vast amounts of "Terpenes" whilst also stay ever vigilant against mold ! Thanks to all those videos I've watched on youtube.. id like to think this was one of my most successful parts of this process.. Things to Note; Terpenes start to seriously evaporate at temperatures 68F or 20C you need to stay as cold as possible whilst bringing the Relative Humidity in the space down into the 40-30% to stay away from that nasty mold ! I used my cold storage room in the basement.. with a dehumidifier running to keep the space at 45% RH & staying at a constant 15c. All while spreading the hash as thin as possible across parchment paper, on top of the white screens with a fan moving air across both sides of the paper. Pictures 36-38 These are some macros i took in the middle of my drying session I fell in love with the colour. Yes i know the black spots are plant material but they will get caught when i bag the hash & squish the oil out. Thing to Note; at this stage it is important to ensure you 'micro plane" the hash down as fine as you can whilst staying weary of the temperature... any "chunks" will hold pockets of moisture.. that lead to potential problems..ie; mold ... Picture/Video 39-41 Successfully planed bubble hash ready to be bagged and Squished ! Picture 42 Ive decided to follow Pedro.. from Pedros Grow Room and double bag to be on the safe side so i don't have any blow outs. So thats One 25u bag inside one 160u bag ! :) Pictures 43 This is almost 3 grams of the bubble hash from above, already melting in the bag.. this is where i ran into trouble again lol things started getting to warm in the house and i was only able to get one of the three squish's i did on video :( things started getting sticky. Picture 44 This is basically just a photo of the equipment I'm using; 3x5 LowTemp Cage in the frame I built myself, with a 20Ton bottle jack. Something to note here is this is an older Lowtemp model with only a single heating zone which is which i have it closed here heating Both sides of the press :) As well as the importance of having adequate pressure on your plates.. my rig is very overkill for the size of hash bags..lol Video 45 Here is the lovely press video.. its didn't quite work the way i wanted either lol my directional folding wasn't quite tight enough for a big "drip" :) &the Press was set to 65°c Photo's 46-50 are pretty self explanatory :) I had a blow out.. but still managed to pull an 80% return from the hash once squished...& yes it tasted amazing :) Was it worth it in the end... that could be debated.. for some..i understand..its not your thing, but for those of us that are interested in making our own concentrates.. free from Solvents... I wouldn't make it any other way :) If even ONE of you reading this diary finds it helpful to reference for ANYTHING.....even if its "what not to do" ill consider it a success ! Thanks again for tagging along on this garden adventure.. its been one heck of a journey ! Much Love from B.C. Canada, Until Next time, Cariboo

3 of the ladies are in flush will be cutting them down within the next or 2 & the other 2 probably have another month left! Fingers crossed for harvest!🤞🏼✌️🏼🌱

So this week was the first week of flowering! 😊 lovely. She has stretched just a little bit and will expect some further stretching. Quite glad of this as my green house is quite short. Weather has been colder and slightly damper this week so she probably hasn’t been at optimal conditions. Gave her Some extra vegetation and bloom to help through this transitions. Also added a nice scoop of BatGuano to ensure she has enough P in the near future.

Although the yellow appearance this lady has still been growing at the same rate as the rest and shooting out the side branches nicley , she is a week behind the rest due too the first seed not germinating but week by week progress has been the same as the others

Not much to report this week. Really impressed with the results so far from the Mars hydro TS600 the bud development seems to be pretty good. This strain is producing a lot of trichomes and the smell is starting to pick up at good bit now going into week 6. Lowered the amount of Canna A an B feed to 2.4ml/L and PK13/14 to 1.0ml/L. Some light defoliation to help get more light coverage to the lower buds.

This grow with the TSW2000, FC4800 and 8x8 Grow Tent has come to an end🤘🤘. I'm so happy with the results mars hydro has done👍. Best lights you can get in my opinion and TONS of other people agree with me on this too👍. I always say mars hydro gets em frosty and their lights DID get em nice and frosty and the buds are so tasty and smell awesome🤘. I trimmed up 6 plants so far. Got 9 more to go. And it seems like I get a 1liter Mason jar per plant and is about 2 ounces per plant. Some are a bit more than 2. Not a huge haul per plant but I'm still very happy with it because the quality is amazing. I will never want to use anything but MARS HYDRO. Extremely satisfied with the entire grow with mars. The weed quality is very good and controlling the heat was simple because they don't get that hot. The lights were very easy to setup and so was the tent. I STONGLY recommend any products from Mars Hydro. You will not be disappointed 👍 Thanks for following my grow and good luck to all my friends and remember to have fun with your grows🤘🤘 rock n roll a joint everyone🤘🥁🎸 FOR EVERYTHING MARS HYDRO VISIT: www.mars-hydro.com PROMO CODE: rocknroll VISIT THE ALIEXPRESS STORE: @marshydro_aliexpress2 Instagram: @marshydropenny https://youtube.com/channel/UChU5ZWwNi-DvnO3oWVU3ceA Thanks for taking the time to read and check out my shit🤜🤛 GET THE MAX FROM MARS👍: Welcome one of  the newest members of the Mars Hydro family🤜🤛🤘. The Mars Hydro FC 4800 480W LED Grow Light can accommodate up to a 4' x 4' area for flowering. It has OVER 2000 LED chips consisting of the best selling Samsung LM301B diodes which has a Luminous Efficacy of: 220 lm/W 0.2 W, 3 V mid power, Osram 660nm Diodes, Infrared light and UV LIGHT👍. It boasts the incredible efficiency of 2.8 µmol/J, maximum 2.5gram yield per watt with 30% higher Average PPFD. This High-intensity spectrum is beneficial for plants at all stages - from veg to bloom, and creates Big dense Buds👍. achieve 50% higher yields & quality compared with the old lights! Only consumes 480W for 4x4ft personal grows, and 3x3ft for commerical grow. It comes with a dimmer and daisy chain function with a  maximum of up to 15 lights, the master light controls the rest👍. Wide 6-bar design offers even & wide canopy coverage and can maximizes your grow space. slim 180° FOLDABLE DESIGN... YES I SAID FOLDABLE🤘🤣 , making it compact and easy to install, it's IP65 WATERPROOF and will give you no worries while growing in a humid environment and makes it a flexible high performance commercial grow light for enormous  SUPER FROSTY yields.😛😛😛. MARS GETS EM FROSTY BOYS👍 AWESOME HEAT DISSIPATION: The Low energy consumption FC4800 growing light has 6 passive-cooled bars and an aluminum heat-sink a removable driver  you can upgrade later or have it outside your tent. with zero noise  you can save up to 50% in your electricity bill compared to HID's or HPS lights! It also has a removable driver so you can upgrade it in the future or have it outside your grow space for better heat control in your growroom👍 UPGRADED FULL SPECTRUM: Yield Max Spectrum with enhanced red (Top-Bin Samsung 3000k-5000knm, Osram 660nm Deep Red), speed up blooming & fruiting, perfectly suited for full-cycle growing. The FC4800 LED grow lamp was born for Big Buds, perfect for commercial, grow tent, grow room, hydroponics, and all soil grows.👍 THE BEST SAMSUNG DIODES: THE FC4800 has Top Bin genuine Samsung Osram Diodes, combined with remarkable 2.8 µmol/J Efficacy, 30% higher Average PPFD, 50% less energy consumption, to maximize your yields. They give you a TRUSTED 3 years warranty 100% Satisfactory guaranteed!!! The MARS HYDRO 8x8 Grow Tent interior is made of a unique diamond design mylar which is highly reflective. (Other companies mylar and reflective rate is as low as 50%, and it won't provide efficient light. They use thick 1680D oxford canvas, and being double stitched, it is tear proof and perfect for locking in the light. Their grow tent keeps 100% of the light inside the tent and helps your plants absorb more light. EXTRA-THICK material means No light leaks or rips at all.👍 Strong Stable metal corner adapters and poles are the trustful supporters of the tent. It's very sturdy, neither rusting or paint flaking off. quick and easy tool-free setup. They use heavy-duty metal zippers, with double layer black lining, by far the best on the market which creates a light-proof seal. The Easy observation windows are made by double layers of cloth. Observe the growing conditions of your plants without opening the tent and avoid disturbing your plants. The observation windows also serves to dissipate heat and ventilate the air. The tent includes 2 removable waterproof floor trays to hold soil and water. The removable tray can be taken out to wash easily. They guarantee the grow tents are easy to install even if you've never done something like this before. Clear Instructions and no tools needed! They also offer 30-day unconditional refunds for quality problems. Just contact their friendly 24 hours customer service 👍

I'm happy :) I couldn't do it as it should have been, my ph meters broke and ruined everything :( well, but I'm very, very satisfied with the result :) a big thank you to my teacher :)@AsNoriu you are super :) without you it wouldn't have been possible :) I learned a lot of useful information from you :) the house is full of lemon aroma :)

Still running into def. but they are still holding strong, great resin production and strong sweet sour smell on the sour alien livers and a pungent lime smell to the alien vs triangle 2 more weeks fore the sour alien and id say 3 more weeks for the alien vs triangle.

I was quite happy to see no more signs of Cabbage Loopers. I awoke to rain this morning so spent part of the day self-supporting the heavier branch sections. All in all everything is super sexy.

QUESTION TO EVERYONE READING THIS: My tap water is pH 8.3 (yes I know right ?!) Adding the BioBizz nutes brings it down to pH 6.2 - 6.4 depending on the amount which is great. Now, I dont really care about runoff pH that much, doesnt tell me a lot imo but I measured it twice, last time it was 6.8 this time it was 7.1. Is there anything to worry about or is that just irrelevant? Thank you guys :) Day 48: Watered the G13 Haze with 650ml Water and 2.8ml / l BioGrow, 2.8ml / l BioBloom, 0.7ml / l TopMax which is the equivalent biobizz week 7 feeding schedule with 70% strength on BioGrow & TopMax and 90% strength on the Bloom. Therefore, dont mind the leaves hanging down, I just watered before taking pictures. Also redone some of the LST by changing the "angles" of the side branches to use up space more evenly. Tied down a bit more aswell to even out height differences. Looks great so far, but the G13 Haze is quite a bit behind in budding, the Liberty Haze is throwing Pistils everywhere, the G13 Haze just started showing the first noticeable preflowers with pistils on the nodes. Day 45: I really wanted to try serious and "professional" training methods. Defoliation was obviously needed, I couldnt even see what was going on below the plant. Removed all leaves except on the top 2-3 nodes of each branch. Then I did some heavy LST to move the side branches to the outside for filling up space. I hope the center will grow some branches at some point. MOST IMPORTANTLY, since I wanted the main branch to slow down growth a bit, I twisted and "mashed" it between two fingers until I could hear a snapping noise and the stem became weak like gummy. It takes a lot of courage guy! A LOT. But it seems to have worked, the stem is not broken and I managed to tie it down without bending the whole plant. I am so excited on how this is going to turn out. ~Watered 600ml today Day 44: So yeah, definitely stretching ! The internodal space is way bigger than I'm used to from growing short indica quick ones. Funnily enough, the G13 Haze does'nt give off any smell at all apart from typical "green plant" smell (Just noted that because the Liberty Haze smells quite strong even though it doesnt form buds yet). Did some very very careful LST which looks good for now. I want to remove a lot of leaves and little side branching from the bottom as soon as the plant grows a bit bigger so I can access the bottom part better.

Day 2 - LST and topping/mainlining where possible before flowering Both plants have broad leaves blocking light to the canopy

During week 7 I accidentally snapped one of the branches while defoliating. It was a clean break but nearly snapped clean off. I have managed to prop and strap it up so hopefully with a bit of care she can hold on. It's now been 5 days since it snapped and seems to still look healthy so keeping my fingers crossed 🤞 Other than that this girl seems to be coming along really well. She has a lot of bud sites and seems to be taking nicely to my DIY Aero/Hydroponic system. I'm really pleased with how she is turning out for my first ever grow and I'm looking forward to seeing her at harvest! Happy growing 🌱

Cool strain to grow, if I grew it again it would be in a 5 or 7 gal smart pot. Was hoping the smell woukd be more in your face and it could be better after the cure but as of now it's like a 7/10 what I was hoping for. I had some high humidity at points when I switched tents so maybe that's why. Overall impressive by seedsman I've had good results with their genetics.

D08 - 02/10 - 4 girls of 5 are very close to the ScrOG net. I think I'm going to tied'em up tomorrow. I decided to wait to cut off the lower branches of the other girls because I need more time and I don't want a quick grow. D09 - 03/10 - Still waiting D10 - 04/10 - They are arrived. Made first LST to keep'em down... D11 - 05/10 - continuing LST. Very strong girls ! D12 - 06/10 - I'm impressed how the mother plant is strong. So are the clones, just incredible. D13 - 07/10 - Made a big defolation and topped the main branches. All the girls must remain down, else I'm going to have big issues ! D14 - 08/10 - Continuing LST under the SCROG. I cutted the secondary branch trying to do a main lining.The girls are very hard to manage, I think I'm go to double the scrog waiting to move them in the other room.

2/12/25 top dressed with 2 tsp grow 1 tsp microbe and 2 tsp bloom. this genetic is always sooo freaking frosty. shes already starting to frost up on the fan leaves. finally looking like shes in flower. it took her awhile to get started i feel like compared to past grows/ other Cultivars. 2/18/25 she has a very nice and even structure to her. a bunch of tops that are 3-5 node top colas with a nice disconnected set of buds after an inch two space between the nodes. frosty gassy and fairly large considering pot size.