~Entry for the 'Best Rarest & Smallest Pot by Seedsman' contest~ Starring 🤩.... ~ Seedsman Zkittlez Auto ~ Zkittlez (Grape x Grape Apple) Auto x Auto Fruit (Auto Fruit Cheese x Auto Blueberry) Zkittlez Auto is one of the very sweetest-tasting auto strains available anywhere. It is a sativa-dominant (60%) strain that was bred from Zkittlez (Grape x Grape Apple) Auto crossed with a male Fruit Kush Auto, the latter a remarkable fruity strain bred from Fruit Cheese Auto and Blueberry Auto. Growers can expect to harvest some good yields of high-THC buds. Zkittlez Auto remains a fairly short plant, rarely exceeding 120 cm. in height wherever it is grown. This is a vigorous plant which is able to metabolize a high level of nutrients and she's a thirsty girl too! If growing indoors close to neighbors it is strongly advised to ensure good and effective carbon air-filtration in order to neutralize powerful odors. This strain's life-cycle is approximately 90 days from seed to harvest. The leaves on this plant are big and wide serving to convert every lumen available into Zkittlez goodness. Indoor growers should obtain between 400 - 500 gr/m2 while plants cultivated outdoors will produce slightly more at 500 - 600 gr/m2. Lateral branching is very good and it is recommended to use supports/ties to prevent snapping and keep buds close to the light source. This strain's scent is sweet and fruity with candy and berry notes. Its high-THC has been measured at between 21 - 24% with less than 1% CBD. The effect is well-balanced, cerebral and euphoric, and is very good for social situations as well as for relaxing in front of the TV either alone or with company. It also has the added effect of helping to relieve chronic pain, helping with nausea, insomnia and depression as well as stimulating the appetite.** **Credit to Seedsman.com ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ~ The Setup ~ ~ Grown in a 2qt plastic popcorn pot filled with Mother Earth Grow 70/30 Coco/Perlite with Xtreme Gardening Mykos added. ~ Seed was germinated directly in the medium without any 'pre-soak' ~ Feeding will be by Dutch Pro Nutrients ~ 24hr light cycle while germinating ~ 20/4 light cycle after first leaves appear. ~ 4x8 Gorilla Tent ~ HLG 650R w/ 30w Supplemental UVA Bar controlled by a Trolmaster Hydro X controller set for a 15min Sunrise/Sunset simulation. (also a HLG Blackbird for additional side lighting if necessary) ~ Supplemental co2 controlled by an AutoPilot APC 8200 co2 controller ~ AC Infinity Cloudline T6 with Controller 67 using a Terrabloom 6x24" carbon filter ~ De-Humidifier and Humidifier when needed. ~ 14k BTU IdealAir portable A/C unit plumbed into tent for temperature control. ~ BlueLab testing instruments ~ Two Hurricane 18" oscillating fans ~ Two 6" Clip-on fans ~ Two 10" floor mounted fans ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ The Harvest: After checking her trichomes which were at 90% milky, I placed the Zkittlez Auto into complete darkness for 72 hours. While in the dark I maintained a temperature of 65-68℉ and a RH of 40%. After three days in the dark I removed the Zkittlez Auto and all I can say is WOW! All of the flowers on the Zkittlez were just covered in trichomes and it had a super strong sweet/fruity aroma that hit me right in the face!😍 I cut the Zkittlez and hung her in two sections as the flowers were huge, and I wanted to make sure that there wasn't going to be any issues with air circulation around them possibly causing issues. It's wintertime here now so I took advantage of the low temp's and RH hanging the Zkittlez Auto in my attic. I sealed off a section of the attic from any light leaks and installed a de-humidifier, fan and humidifier along with a hygrometer which I suspended at the same level as the plant was hanging which give the most accurate reading of temp/RH. After hanging the Zkittles, I adjusted the fan direction so that it was not blowing directly on the hanging plant, but kept the air slightly moving in the room. I set the de-humidifier for 50% which I run for the first 24hrs to knock down some moisture in the plant, then set it to 60-65% for the remainder of the drying time. The Zkittles Auto hung for a full 12 days, during which I checked on it daily to empty the de-humidifier and make sure that the environment stayed on point. After hanging, it was time to trim this beauty up and get her flowers into glass jars to begin the curing process which I prefer to take at least one month, preferably 2-3 months to really get a good cure and allow all the starches to convert to sugars, the remaining chlorophyll to metabolize and the terpenes to form their bouquet! Trimming the Zkittlez Auto by Seedsman was a breeze and resulted in some tightly stacked and absolutely gorgeous flowers that are loaded with shiny trichomes that sparkle, and a sweet and fruity aroma that will make your mouth water!😍 I was super stoked to harvest almost 100g from this beautiful autoflower that was grown in a little .5g plastic popcorn pot that I had saved from a trip to see 'Top Gun Maverick' at the theater and I can attest from cultivating Seedsman's Zkittlez Auto in the past, that with a bigger pot, it is capable of some incredible yields! All in all, this grow was super fun and easy! I highly recommend Seedsman's Zkittlez Auto to everyone from novice's to master growers as it NEVER disappoints to produce some mind blowing fruity buds! ❤️❤️❤️

Upgraded from 200wts - 450wts Marshydro ts 3000. So far so good!!🤩

Hey yall, It's been a minute, I have been super busy out of town again. All is good though, the flowers are fattening up. Still not a fan of Beaver Seeds. I DO NOT RECOMMEND BEAVER SEEDS, just to be clear. They don't respond, like super sativa club, lol. I email and contact their website, zero response. So pick a breeder you can trust and has open communication. Otherwise they are greedy and most likely have shitty genetics. I popped two feminized seeds, one was a runt from the start, she died when my Temps hit 90 Fahrenheit, which is absolutely 💯 bullshit. I use potassium silicate, frass, aloe and everything that should help with heat stress, so this one is on the breeder. Anyways, they hardly have many trichomes, despite my shit being dialed to the max, PPFD. VPD, water only soil with dry amendments and weekly compost tea applications. That always dumps trichomes for me. Genetics are 90 percent of the game, we can control up to 10 percent as the growers. Well you can see what I mean. Week 6 of flowering now, so yeah I missed a couple weeks, but you know how it is. Life is nuts and you have to work to pay those electric bills. I already popped new seeds from a much better breeder, I literally cannot wait to chop these girls to pieces, and making RSO out of the entire run, I ain't even smoking this shit. Lol. Sorry I didn't throw up any tutorials this week, but check previous weeks for detailed recipes. I did add fermented Banana peels, overly ripe ones to help push flowering maturity. Also added fermented kiwi, overly ripe again to push end of flowering. Also added Willow water, and a ton of fermented aloe and some frass I got from a buddy. Love yall! ❤️ hope you get better genetics than me. Oh and yes, if you get a chance, tell Beaver Seeds to F*** themselves lol, 😆 🤣 😂 😹 Peace out girl scouts, oh and yes, Berner did not make GSC, he stole the name and the first OG cut of Girl Scout Cookies was from San Francisco. So the real breeders don't make shit up, they work their strains and stress test their genes to ensure there is no bullshit, get in touch with your breeder. Check out 808 Genetics, I think that dude has it going on, he stress tests everything and has a great Twitch stream, Check him out! ❤️ 💙 💜 💖 💗 💘

*Week 4 Flower 09/24* Both Mimosa girls appear to be running fine with Mimosa (1) running a little behind but is catching up accordingly. Small oversight in early growth resulted in a minor stunt but she is improving dramatically. Water Feed has increased by half a gallon ( 1gallon clean - .5 gallon nute feed) *Week 4 Flower 09/28 - Mid week update* Both plants are flowering accordingly - Mimosa (1) is a bit taller then Mimosa (2) Buds are becoming dense and covered in trichomes. No deficiencies - No areas of concern - Potassium and Phosphate feeds continue *Week 5 Flower end of week recap - 09/30* Both Mimosa's are flowering nicely - Budsites covered in frosty trichomes. Mimosa (2) looks shorter but that is because her COLA was tied down to expose bottom budsites.

11/20 I did quite a bit of feeding last week and her top is getting very heavy. I’m having trouble keeping them standing up. I was going to take down one branch but I think it would cause the other branches to fall so I’m just gonna try and keep balancing them maybe for another week then I’m gonna cut them down. I have three more and another tent. I’m flowering them at between 86 and 90 W with the Mars Hydro lighting seems to do the trick I’ve had the same plant growing I think for over a year now I keep taking clones and then I take another clone. This is the first time I’ve attempted to do that and now I can see. I’m glad that I did because I made up for seeds that I managed to kill along the way. I always blame the seed company and then I find out a year later that it was something I did so I try not to complain too much about that. 11/21 I took down one of the branches yesterday she was giving me trouble. I sent a message to the other ones. I think it helped they really starting to produce now. They’re really starting to fill in now. I could take them down but I want to keep them going maybe two weeks as long as you’re still bulking up I want to keep going and I have one branch that will probably dry down to, a little more than half an ounce. It’s not really big, but it’s pretty nice and considering these were just clones these are branches. If you look early in my other diary, they work great. They’re looking a little crispy from a little too much nutrient I’m gonna give them just some plain water tomorrow and start backing way off on all nutrients. I think they have about another two weeks to go maximum. They’re really filling in nicely if I don’t stress them out they fill-in really good. Should probably get at least a dry ounce off of each of these branches. 11/22/23 I dried one of the branches didn’t get a lot. It’s very nice densely packed. Smells good it’s enough for me. 11/25 Saturday morning. I took a branch this morning. I have two on one plant and three on the other still going. I’ll keep them going if I can if they’re still growing I turned the light down to 89 I don’t really benefit from light that’s too bright toward the end of the grow it just melts the resin it just is not good for them and they seem to go just fine. I have another blackjack clone in another tent that I am going to try and do the whole grow at 93 W with this light so far it’s going just great. I accidentally left it there and if I can do that and not stress it, I might get better plants at lower wattage. 11/26 these three blackjack clones are growing perfectly at 93 W. I can’t believe it. No sign of stress of any kind so I’m gonna keep it at this wattage. Also it keeps the temperature super low. I have the driver outside the tent so it doesn’t make that much difference and one of the pots I didn’t fill up with quite as much soil probably 2 gallons and they still are doing good so blackjacks are very fun to experiment with and it’s a great smoke I have one of the branches drying right now and she seems to get more resins as she’s drying it’s incredible. I have two that are flowering that are just about ready. I overdid the fertilizer so I’m going to do a clean today with the general hydroponics. I got a gallon of the flora clean. I’m going to leave them at 89 W for the rest of the grow that should be good enough. It’s great that I can do this at 89 W. I use the general hydroponics Flora, clean and watered both of them. I did 10 mL per gallon and I did about a gallon and a half. There was a lot of runoff. It was really gross. I have bugs in the soil. I sprayed the bag and the soil for bugs.

Week 1 of flower, pics and video taken on day 6. Lollipopped everything beneath the scrog 3 days ago. All 4 plants are looking healthy and happy.

Legend Timestamp: 📅 EC - pH: ⚗️ Temp - Hum: 🌡️ Water: 🌊 Food: 🍗 pH Correction: 💧 Actions: 💼 Thoughts: 🧠 Events: 🚀 Media: 🎬 D: DAY, G: GERMINATION, V: VEGETATIVE, B: BLOOMING, R: RIPENING, D: DRYING, C: CURING ________________________________ 📅 D105/R01 - 28/02/24 ⚗️ EC: 0.9 pH: 5.2 🌡️ T: 21-25 °C H: 50-65 % 🌊 🍗 💧 💼 🧠 Ripening starts 🚀 🎬 Added timelapse and screenshots and monthly rate of T-H and VPD 📈📈📈 from TrolMaster App Translate ________________________________ 📅 D106/R02 - 29/02/24 ⚗️ EC: 1.2 pH: 6.7 🌡️ T:21-24 °C H: 50-65 % 🌊 🍗 💧 Added pH+ 💼 🧠 If someone who followed the diary from the beginning is asking himself what about mother plant "Mamma Aglio", here I posted some picture of her which demonstrate the difference between a bad and a good grow 🚀 🎬 Added pics of Nicole and pics of "Mamma Aglio" to show the difference between a bad and a good grow with sounds and TrolMaster logo. Added usual timelapse and screenshots. ________________________________ 📅 D107/R03 - 01/03/24 ⚗️ EC: 0.8 pH: 6.4 🌡️ T: 20-24 °C H: 45-65 % 🌊 2L 🍗 💧 💼 🧠 🚀 🎬 Added Timelapse and screenshots. 4 pics added ________________________________ 📅 D108/R04 - 02/03/24 ⚗️ EC: 0.8 pH: 6.7 🌡️ T: 20-25 °C H: 45-70 % 🌊 1L 🍗 💧 💼 🧠 🚀 🎬 Added Timelapse ________________________________ 📅 D109/R05 - 03/03/24 ⚗️ EC: 0.8 pH: 6.7 🌡️ T: 21-25 °C H: 45-65% 🌊 RES Changed 💦💦💦 🍗 💧 💼 🧠 I'm starting the flush, as trichomes look milky and quite ready. In this last week the ripening will be complete and th girl would be ready for harvesting. 🚀 Flush started 🎬Added 8 pics of trichomes, Timelapse and sceenshots. Two pics and two videos of my "garden's pre-harvest magic" 😋😋😋 ________________________________ 📅 D110/R06 - 04/03/24 ⚗️ EC: 0.2 pH: 7.5 🌡️ T: 19-25 °C H: 55-65% 🌊 🍗 Flawless finish 💧 💼 🧠 1 day with pure water and now I added Flawless finish 🚀 Flushing 🎬Added Timelapse and sceenshots ________________________________ 📅 D111/R07 - 05/03/24 ⚗️ EC: 0.2 pH: 7.5 🌡️ T: 20-25 °C H: 55-65% 🌊 🍗 💧 💼 🧠 🚀 Flushing 🎬Added 8 pics. Added timelapse and screenshots. I also prepared a timelapse of the entire week with some music 🎵🎵🎵 and weekly rate of T-H and VPD 📈📈📈

2ª Settimana di Fioritura 💐: La bella e vigorosa Critical Lemon⚡🍋, Continua nella sua crescita e mette in mostra tutti i suoi nuovi fiori!😍 Sotto il vigile controllo di TENT-X 🤖, la piccola sta dando il suo massimo nel vaso da 6,5 litri...... Abbiamo settato anche alba e tramonto con una durata di 10 minuti (figata) ☺️👏🏻👍🏻

9/4/24 starting to look happier. also since shes had to reveg a bit, i got a peak into what she will look like in early flower. she will get dark and the fan leaves are covered in trichomes and that was only preflower. 9/9 topped the two

I topped the 2 last plants and started LST on all of them without any problem. The growth was pretty impressive this week, especially for the Wedding Cheesecake which is clearly bigger then the others. I had to add some supports to compensate the height difference between the plants. I removed some leaflets here and there during the week to give some light to the lower branches without removing too much leaves. I increased the light power to 75%. I will probably give them another week and then switch to the 12h/12h schedule. Plants heights at the end of the week : ------------------------------------------- Gorilla Cookies : 29cm Purple Lemonade : 22.5cm Wedding Cheesecake : 37cm

First day of chop! and my dry room stinks like fresh wild garlic. I think she's around 500-750 grams in weight, i don't own big scales so couldn't really check. The grow could of been better but around week 5 I had a serious accident so I've had my friend look after my girls so couldn't really train and take off useless popcorn so she looks very airy to me but packed in crystal. I'll update once dry.

We are almost at the magic moment, it is about to go into flowering and the vegetative phase is practically over in a few days. Our Purple Urkle by Zamensia is a very beautiful plant with a good internodal distance and is developing very very well. We have just done the last topping that brings her 16 tops, 16 small clones of the main cola that will come up I hope at the same time and all together and above all I hope that the cold will give us a great resin and a beautiful coloration. During the topping the use of nitrogen is a very delicate subject. The cuts of the topping slow down the plant and the leaves tend to grow bigger going a bit into over, it happened to her then you detach and it tends to discharge now we are at the moment that we are starting to give nitrogen again to then go into flowering. It is a process that must be nuanced very delicately. Ideally it is to start by preparing the soil with fertilizer and add if necessary. I over-fertilized the plants a bit but it's something I've always managed very well once I got to flowering. Next time we'll add some fertilizer to the soil with this technique it's very suitable. Wait for the uncle BreadandBuds.... We are always using soil, feeding and all the recommended additives from Plagron 100% organic, we have only lowered the amount of grow in this topping phase for the reasons mentioned above. ---- Decide on the right soil and calculate your fertilizer sheet based on the soil on the official website. -- www.plagron.com Try a seed of this strain that drives us crazy.. ---- https://www.zamnesia.io/en/11168-zamnesia-seeds-purple-urkle.html Zamnesia Description // A direct descendant of a Mendocino Purps phenotype, Purple Urkle is a high-performance cultivar from Zamnesia Seeds. This feminized, indica-dominant strain is sure to win over any cannabis grower. With a THC content of 20%, Purple Urkle has a lot to offer from seed to harvest and beyond. A grape-flavored adventure, Suitable for indoors, outdoors or in the greenhouse, Purple Urkle is a very resilient strain. Growers will be impressed by how easy this cultivar can be managed. Purple Urkle can reach 120cm indoors and 160cm outdoors, but if you want more control over the height you can use the LST technique. Purple Urkle has fantastic flavors and aromas that intensify during the flowering phase. Regardless of the method of consumption, Purple Urkle offers tangy, fruity flavors that lean towards notes of grapes, berries and plums. The effects of this strain are soothing and relaxing, with uplifting sensations that make the experience suitable for any occasion, whether in a social setting or alone. All the best that mother nature can offer is on ---- www.zamnesia.com

shoes size 44 eu :DDD

Going to start feeding GHE CALiMAGic 2.5ml per gal, and Floraflex V1+V2 at a 1:1 ratio of 1.5 grams per gallon PH 6.1 daily. Also adding a CO2 generator in hopes to promote vigorous growth early on since this is supposed to be a quicker flowering stain. Growers Recharge will be applied once a week on Saturdays from here on out.

So i trim the old leafs and leave it to grow on the new ones i leave as is and keep adding the ab solution. It grew so quick so big, i trimmed the big leafs and keep it focused on solution every 2 day 3 liter

Buenas noches familia, de nuevo actualizamos el diario, y acabamos la cuarta semana de floración, vaya brazos laterales que están tirando, se van a poner hermosas, se las ve sanas y vigorosas, nota mucho la forma sativa de sus hojas así que veremos lo que tardan en florecer. Ph controlado a 6,5 y humedad por debajo de 45% not bad las condiciones temperaturas mínimas de 20 y maximas de 27,5 Grados. Al atar las puntas los brazos tendieron a ir a la luz y gracias a eso la planta está tomando la forma de la esquina.

4-2-2021 Now starting 2nd week of flower. Look at her grow would you expect anything less from a Crop King Seeds seed No Way!. She is far behind the others but doing great just the same. So easy so far to grow this strain so not sure what the fuss is all about. I did manage to bend her under the string so technically she is a Scrog. I just did that so to spread her out might get a few more larger buds out of her.😎 Love how she is doing so far. Keeping the PPM'S Steady for now and added some Seaweed stuff for root growth. We will see how she reacts.💪

Let´s start a new week 😎👌 Day36 very sunny and warm... "Hilde 2.0" goes well 😎👍🙏

Week 6 in veg done and dusted! She grew 12cm! Day 42 - I clipped off about 6 huge fan leaves to allow light to hit her lower branches. This is her last day of 20/4 lighting. It will be 12/12 from now on. 💪