Que pasa familia, vamos con la segunda semana de floración de estas Orange Sherbet Fast Flowering, de FastBuds. Agradezco a Agrobeta todos los kits obtenidos de ellos 🙏. Vamos al lío, El ph se controla en 6.2 , la temperatura la tenemos entre 22/24 grados y la humedad ronda el 50%, añadimos ya varios productos de la gama de Agrobeta. Las próximas semanas veremos cómo avanzan, trasplanté a maceta definitiva. Agrobeta: https://www.agrobeta.com/agrobetatiendaonline/36-abonos-canamo Hasta aquí todo, Buenos humos 💨💨💨

This week has went by ok beach ball is growing well new growth has come in pretty well the other plant is not happy with the pot slow growing plant

Update of Goofiez 2 !! It’s incredible this strain is so strong and fast grow !! Stay tu ed

Die Ladys sind jetzt ordentlich am wachsen

I'm happy. I wish the weed would last forever. 🍊 Thank you, @DutchPassion_Official for the opportunity, I'm definitely a fan from now on! ❤️

June 7 - We ordered some new lights last week, they are 240w kingbrite samsung lm310h with uv/ir, 3000k, and meanwell drivers. We setup the new room and moved the girls into there. After a bit of LST and a watering (with nutrients) at roughly 7ph, they were ready to go under the 2 new lights and the same SF-1000 we have been using in this grow. The new room is a 12 ft enclosed trailer. I moved everything from the small tent into this. I put clear poly on the walls, floor and ceiling. I put poly on the shelf I am going to be keeping in there as well. I bought 50ft of 6mm mylar and lined the floors, roof and sides with it. I plan to get some reflective tape to seal everything and to cover the wood. I did not get much of a chance to watch temp's today as they it was later in the evening after all was said and done. The inline fan blowing in air from outside. June 8 - 9 AM i checked the plants, they were at 25.2 and 50% RH. Late through the day I had checked and we had gotten up to around 32 degrees. So I moved the inline fan to the closer vent, hooked up to that, and had the air blowing out of the trailer with the inline fan sucking it from above the lights. I then added oscillating fan and had it blowing air on the left side of the room so it would somewhat circulate once I closed the doors. I then checked at about 9pm and we were at 22 degrees. Definitely noticed a decent amount of growth already. I have the lights on a 22/2 cycle as I was worried about the heat at night time. June 9 - Some great growth from the girls, still having problems controlling the temps in the afternoon. I decided to prop the door open a bit to have a constant breeze throughout the day while I am at work. Decided to do some more LST and also a bit of defoliation. I took about 25% of the leaf's that were blocking the new growth as it was getting a bit bunched up. I was then told the leaf's are almost solar panels for them. So from now on I will be trying to just do some tucking unless needed. The leaf's I removed were most of the damaged leaf's, I am not to sure if that makes much of a difference. I gave them a watering with only water as there is a potential I am getting a bit of a nutrient buildup along with the PH problem. Or potentially the reason for the ph problem is nutrient buildup. After watering with A PH of 7 I got some run off and tested it. The smaller plant gave me a PH of about 5.5 where the bigger one is around 5.0. June 10 - Plants are looking happy and showing tons of growth. Seems to be trying to stretch outwards. Not a ton of sign of PH issues showing so potentially getting it under control. Still a bit of damage to previous leaf's but it is what it is! The last few days I have been leaving the door open a bit in order to keep the temps down. I decided to test something and turn the lights off (automatically) at 11AM and back on at 5PM so light schedule has now changed to 18/6 and it seems I may have figured out the issue. We haven't had lots of sun the last couple days so it hasn't been to hard and I have yet to know if it truly fixed the heat issue for now. (I will be looking into a ac unit as well since it typically gets to around 30-35 around here. June 11 - Pulled some of the branches back down and added a few more LST spots. Seems we have a good amount of growth from the smaller plant out of the 2 topped spots. Unfortunately it looks like I fucked up on the bigger plant and only one of the nodes seems to have new growth. I will continue to monitor that but I think I cut the node to low and also to soon. Other then that, the girls are doing great. They seem to be absolutely loving these new lights. I gave them some nutrient water today as well. roughly 3L each. They seem to be A hell of A lot more thirsty under these new lights. June 12 - The girls are doing great , they are still just doing growing away. Lots of progress everyday. I am going to be getting a go-pro so I can set-up a time-lapse for the rest of this grow. I received my new inline fan, I got A ac infinity CLOUDLINE T4 with the temperature humidity controller. I am going to be having one fan pushing fresh air in and one fan pulling out the hot air. I will be doing that tomorrow since I have to work today. June 13 - I ordered another 50ft of mylar and that showed up today. I have decided to remove the shelf and add another 3+ feet to the grow space. So today I installed more poly, mylar, the ac infinity fan. I have it set-up to pump in air if it gets to warm. I am thinking of switching it to the output that way if it gets to hot or to humid I can have that air pulled out of the trailer. Right now my other inline fan is the outtake and I just have it set on full. Overall I think everything is set-up a bit better and more accessible. I will be putting my 2x2 tent in there at the left of the doors so I can have a veg room when these 2 are in flower. I plan to have 4 in veg and 4 in flower for the next grow. Still waiting on JOTI seeds, ordered 3 weeks ago and still have not been shipped. I will be getting those going the moment they arrive. The girls seem to be happy still, did a bit more LST to try to keep everything even, mainly I'm just pulling down on the spots I already have tie wire on.

I didnt take pics of a few weeks

Things are now advancing smoothly, having effectively weathered the majority of the challenges encountered. It's a truly uplifting experience to watch the process unfold, seeing how the plants are developing and thriving. Each day brings new progress, and I am continually enthusiastic about maximizing the sunlight that each plant receives as they continue on their growth journey. In addition to the hands-on cultivation aspect, I'm also diligently working on expanding my clones collection. The plan for the next week or so is to cultivate and ready these clones for transplantation. It's an exciting aspect of the process that helps me stay committed to my ultimate goal. That goal, of course, is to maximize my supply chain and provide high-quality cannabis. This involves more than just horticultural efforts. I am also persistently studying and researching the relevant laws to familiarize myself with the legal process. Navigating the licensing phase is a vital part of this journey, and I am committed to understanding and adhering to all legal requirements to ensure success in this venture. Diary Entry for Growth Project: Day 24 - Today, a slower-growing plant was effectively moved from its soil environment into an idle hydroponic system. With this transition, the count of prospering plants stands at eight, with a couple more still being monitored due to uncertain growth. Significant discoveries include the paramount importance of light distance to the plants, which was underestimated initially. Further, it has been found that genetically modified seeds hold no superiority over the prevalent autoflower seed market. Additionally, the positioning of the plant and the volume of medium placed between the plants and the water source have been recognized as key determinants in accelerating early stage growth. Welcome to the Day 25 update of our grow journal. I must apologize for the slight confusion - although the video says it’s day 23, today indeed marks the 25th day of our journey. I’m thrilled to announce that we’ve had a successful transplant. The plants are now settling nicely into their new environments. The question now at hand is, should we introduce stress training? As we move into days 26 and 27, I have been pondering on this. High-stress training can sometimes stimulate growth, but in our current situation, it might not be the most prudent course of action. This time around, we are expecting all our plants in the grow tent to blossom concurrently. In light of this, I’m leaning towards letting nature take its course rather than intervening with stress training. By doing so, we will allow our plants to focus their energy solely on flowering. The goal here is to encourage the production of dense and frosty buds, the hallmark of a successful growth cycle. Rest assured, we’ll continue to provide the plants with the care and nutrients they need. Remember, every cycle is a learning experience, and we’re on this botanical journey together. Keep checking back for more updates on our garden’s progress.

LJ4Q23 Bolt II SOP LJ4Q23 - 8-Plant SOG from Cuts Objective: - 8 Plants - Single Colas - No Branches - Harvest Lemon Jeffery (Narrow Leaf Phenos): 70±5 days - Light Intensity - Ramp up from 200 - > 40 DLI, at 13 hour ScotoPeriod, will need MAX Light to Achieve - Ramp Light Intensity to MAX ASAP (3 Weeks?) Notes: - Lemon Jeffery handles HIGH LIGHT Well, even within 6” of Light @ ~1800 µMol/m2/ - The challenge will be achieving minimum 40 Mol/day, which in this setup requires 1000 µMol/m2/s @ 13 hour Scotoperiod ______________________________________ Start of Week: [ 2023-12-06, LJ4Q 8:B:1:1] End of Week: [ 2023-12-12, LJ4Q 14:B:1:7] Flower Week 2 _______________________________ Environment Targets (Bolt II): - Scotoperiod: [ 13, h] # Contiguous dark hours daily - DayPeriod: [ 1900, 0600 +24h] - TemperatureMax: [ 82, °F] - RH: [ 70, %] - VPD: [ 0.91, mS] - LightIntensity: [ 850, µMol/m2/s] - LightDistance: [ 16.5, “] Bolt II Fertigation - RLA Medium Chart, Week 2, EC: [ 1.7, mS] - Primer A: [ 6.2, ml, gal] - Primer B: [ 6.2, ml, gal] - CalMag Fuel: [ 2.5, ml, gal] - Silica Skin: [ 2.5, ml, gal] - Lush Green: [ 2.5, ml, gal] - Root Anchor: [ 2.5, ml, gal] - Peak Bloom: [ 2.5, ml, gal] Bolt II Fertigation - RLA HYDRO Chart, Week 4, EC: [ 1.7, mS] - Primer A: [ 8.5, ml, gal] - Primer B: [ 8.5, ml, gal] - Silica Skin: [ 4.25, ml, gal] All Fertigation Add - Plant Success: - Microbelife Photosynthesis Plus: [ 0.5, ml/gal] - Build-a-Soil: - Quillaja20 Powder: [ 0.5, tsp/gal] - South Cascade Organics: - SLF-100 _______________________________________________ Wed Dec 6, 2023 LJ4Q 8:B:1:1 __ Thu Dec 7, 2023 LJ4Q 9:B:1:2 FOLIAR Application: Bolt - CalMag Fuel: [ 20, ml/gal] - Lush Green: [ 5, ml/gal] Install Drain Tray - [x] Install Irrigation Manifold - [ ] Install Drain pump Irrigation Install (When Drip Rings Obtained) - [x] Connect manifold lines to each of 8 drip lines - [ ] Calibrate Drip Ring delivery __ Fri Dec 8, 2023 LJ4Q 10:B:1:3 - We had 500 ml Runoff from 360 X 8: 2880 total: 17% Runoff, which is a good number. - Therefore - if we want to duplicate Initial watering: - Let’s start at nominal 110 ml/ event - 4x a day. 1.8 ml/sec, 110 ml: 61 Seconds, + 5 Sec -> Make it an EVEN MINUTE of irrigation. - [x] Bring Reservoir Operational - [x] Power Chiller - [x] Install irrigation pump - [x] Install circulation pump Irrigation Approach - We’ll use 1.7 ml/sec/line as the Baseline feed. - If we water no more than the Saturation Volume daily . . . - 440 ml/day, Max/Plant Estimates - AirPot Size: [ 4400, ml] - AirPot Saturation: [ 440, ml] - @ 3.2 ml/sec: [ 137, sec] # Max Per Day - Assume 10 Sec ‘Fill’ overhead Per Irrigation HF Fertigation - 4 Events/day - 11 hour Irrigation 4x/day Frequency: 2.75 hrs - First Irrigation 15 Minutes BEFORE Lights On - @ 1.7 ml/sec, 60 sec/event, 100 ml/plant, 4 times a day - 60 Seconds/event, 4X/day EC 3.2 1.7 6.0 ml ml ml Primer A 16.00 8.50 EC 3.2 1.7 6.0 gal total Primer B 16.00 8.50 Primer A 16.00 8.50 51.00 Silica Skin 8.00 4.25 Primer B 16.00 8.50 51.00 Quillaja20 0.5 tsp/gal Silica Skin 8.00 4.25 25.50 King Crab 0.5 ml/gal 0.5 - Loaded ~ 6 Gallons, added another 1 to 1-1/2 to EC: 1.7 Program Irrigation Timer ( Start 15 minutes before Lights On - Time based on ~3ml/sec per line ADJUST When we have ACTUALS). Delivery Max per Plant/day: [ 440, ml] Delivery Frequency/Day: 4 Delivery Period: 2h, 45min Delivery/Plant: [ 102, ml] DeliveryDuration: 60s Usage Expectations - 800 ml/day W 6 Gallons in the res, we’ve enough feed for 28 Days - probably need to mix less. ;-} Fertigation Schedule Initiate Irrigation Irrigation Complete Event 0 18:45:00 18:46:00 Event 1 21:30:00 21:31:00 Event 2 00:15:00 00:16:00 Event 3 03:00:00 03:01:00  Foliar - [x] Resin Bloom: [ 20, ml, gal], [ 1.25, ml, 240, ml] - [x] CalMag Fuel: [ 20, ml, gal], [ 1.25, ml, 240, ml] - [x] Connect manifold feed line to Little Giant Irrigation Pump FOLIAR Application: Bolt - Solar Rain: [ 20, ml/gal] Per Line Delivery, 2 Data Points: 1.87 ± 0.125 ml/sec Let’s go with 1.8 and see . . . Following the rules of Halves - the Pre-Drip ring flow rate was 3.2 per line. With the rings - it’s about HALF, maybe a little more. SO - Ferti9gat __ Sat Dec 9, 2023 LJ4Q 11:B:1:4 GROWER ERROR - Left Irrigation pump connected to POWER instead of TIMER and drained 6 Gal of feed across 8 plants. - I think they’re sufficiently watered . . . ;-} - Gorilla Grow Tent HELD all the water until I could shop vac it out this morning during the grows scotoperiod. - Will report on results after lights on @1900 Lessons Learned (SOP) - ALWAYS ENABLE DRAIN PUMPS BEFORE INITIATING AUTOMATED IRRIGATION - Some might call this common sense, not an SOP… _______________ Saturday Tasks - [x] Refill Res, RLA Hydro Chart @ EC: 1.7 mS, 3 Gal (11.4 Litres) - [x] Primer A: [ 25.5, ml] - [x] Primer B: [ 25.5, ml] - [x] Silica Skin: [ 12.8, ml] - [x] Quillaja20 Powder: [ 1.5, tsp] - [x] SLF-100: [ 15, ml] - [x] Photosynthesis Plus: [ 18, ml]  - [x] Tidy Grow Room Install Irrigation Drain system - [x] Obtain 10’ of 1/4” - 3/8” red tubing for runoff drain - [x] Install sump and catch bucket - [x] Externalize power cord - power up - verify operation - [x] Externalize waste hose output in 2-1/2 Gal Dark plastic reservoir _______________ __ Sun Dec 10, 2023 LJ4Q 12:B:1:5 LightIntensity: [ TBD, µMol/m2/s] DLI13: [ TBD, Mol/m2/d] Need to get to 40 DLI baseline, which at 11 hours of light is 1037 µMol/m2/s @ 11 hours/day __ Mon Dec 11, 2023 LJ4Q 13:B:1:6   Lighting Plan - Increase PPFD 10% until we’ve achieved [ 1000+, µMol/m2/s] - Increasing light intensity will increase nutrient needs and runoff. - STAY ON POINT. FOLIAR Application: Bolt - Solar Rain: [ 20, ml/gal] - Silica Skin: [ 20, ml/gal] Still looking for vigor. The girls still look like they’re enjoying a slumber party. ;-| Evaluate Runoff - After doubling irrigation time ( 1 min -> 2 min), we should have some runoff to evaluate. - IFF NOT: Double Irrigation Time to 4 min - ELSE: evaluate - estimate 10%/min, ~320 ml LightIntensity: [ 850, µMol/m2/s] # The sooner we get to full light, the better. ;-} - 440 ml/day - 44 ml, runoff/day - [x] Actual: [ 500 , ml] We also had an extra 5 or so minutes of feed verifying pump yesterday. Will measure again Tuesday. height range: [ 10, 6, 9.5 avg] - [x] Increased Irrigation Interval to 3 minutes. __ Tue Dec 12, 2023 LJ4Q 14:B:1:7 Irrigation Interval: [ 3, min] Irrigation Delivery per Event: [ 100, ml] Events per Day: 4 Total per day per plant: [ 400, ml] Total per day delivered: [ 3200, ml] # < 1 Gal - We target 10-15% runoff, so we’re looking for 380 - 440 ml runoff per day. - IFF we have MORE than 380 - 440 ml’s - [x] Reduce Irrigation Time to 2:30 (from 3:00) - IFF we have LESS than 380 ml runoff - [ ] Increase Irrigation Time time to 3:30, Re-evaluaute WEDNESDAY - [x] Measure Runoff - [x] Amt: 600, ml - Total Run was 14 minutes. We’re using 100ml/min as the guideline, but believe it’s closer to 30-50 ml/min. ***TUESDAY NIGHT - LAST PICTURE FOR WEEK (Hopefully DRY and Praying)!*** Changed Irrigation from 3 min to 2:30.

this harvest is too early because of my growing condition,

Thanks Super Sativa Seed Club and Mars Hydro for sponsoring this grow . I’m hoping to get a good yield off this plant . I’ll be back with the dry weight in a week or more . Happy Growing 🌱

The plant has started active flowering, is actively fed, feels very well 💚❤️💜

Stardawg is looking like a star ⭐️.. really happy and healthy plant.. looking at it I can confirm it will be the most yielding plant of this run.. buds are big, fat and smelling that sativa that I love.. can’t wait to finish it ✨

Day 42 week 6 Feed a bonide mixture 2nd time in a week. Pest have gotten worse but trying to manage persistently. Growth seems to be picking up. Added a 2nd mars hydro Cree 128 as I got a new flower light. Trying to get them used to the new lights and a better ppfd range as I was using the wrong measurements for the past year of growing around 75 umol range … surprising yeilds though with knock off lights in those conditions looking back on it. Next grow will be smooth hopefully lol Day 47 Top dressed 444 Gia green 2 tbps Alfalfa meal 1 tbsp Kelp meal 2 tbsp Crab meal 2 tbsp Asomite 1 tsp Gradual humid acid 1 tsp Glacier rock dust 1 tsp 1-1.5 tbsp of em bokashi bran .5 mykos gruanual mycorrhizal fungi Also sprinkled some langbeinite on I’m thinking there’s potassium deficiency in the soil mixture with this long veg and haven’t feed much potassium. Leafs showing some signs of it. Added 1 inch mulch layer of rabbit compost/ wood chips and spread some clover seeds underneath. Finally got my silica in the mail so soaked it all down with 3ml or 3 grams of 1 gallon of water split between each plant sprayed into soil evenly. They are already feed so this way just to get everything started under the new mulch layer. Will spray bonide on plants to continue with any pest issues leftover.

8 mains filling out after top and bend, hairs are starting everywhere, every original fan leave has been removed.

Eccoci di nuovo qui!!! Super eccitato per questa nuova collab con Kannabia Seed Company, team davvero al top, che mi ha dato l’opportunità di testare questa nuova genetica e di condividere i progressi con tutti voi!!! Come sempre partiamo nei bicchieri per poi travasare.. Questa volta verrà svolto tutto sotto la Lumatek Zeus 465 ProC, mi aspetto molto da questo ciclo!! WOOOOOOOOOOOW Grazie a tutti per il supporto ❤️🍀🔥

My Lit Marker plant is really taking off! It's growing so fast, and the leaves are getting bigger every day. They have this cool, pointy shape that reminds me a lot of the Black Valentine plant. It's exciting to see how quickly it's developing, and I can't wait to watch it grow even more. Stay tuned for more updates on this beauty! The weather has been absolutely gorgeous this past week! We've been hitting that sweet spot of 70 degrees during the day, perfect for getting outside and soaking up some sun. Then, it cools down to a comfy 50 degrees at night, which is ideal for sleeping with the windows open. I've been loving all the fresh air! I finally got around to building that little wooden planter for my windowsill. It was a fun project, and now my regular plants have a nice new home. It really brightens up the room, and I'm thinking of adding some herbs to it soon. Maybe I'll even try growing some basil!

First week under the Lumatek 600 Pro set to 50% and aporox 40cm away from canopy. Day 7 applied some pruning and supercropped the few taller girls to even out the canopy. I will add a CO2 bag next week as i increase the power to avoid potential light stress.