By continuing to use the website or clicking Accept you consent to our cookies and personal data policy and confirm that you are at least 18 year old. For details please see Privacy Policy and Terms
Accept
Mold?
Hashyanswered grow question 4y ago
That's a hard one to tell. It could either be mold or salt build up.
likes
Complain
Similar Grow Questions
Solved
CannaZen
H2O2 bath for light PM on pocorn/trim, pre QWISO?PM found on trim, post harvest, my bad darnit. *Very light* but I take pride in my work. Personal consumption only. Forums reviewed so lets skip the chatter, will proceed with QWISO. Should I do a H2O2 bath before extraction in ISO? Trim off best plant, Dos Si Do which is strong.
Week 19
Other. Mold
6y ago
1
1
Solved
foyef66149
Is it mold in flowering stage?I've noticed some discoloration in 3 buds and I'm not sure what it is.
I am at week 7 of the flowering stage. The strain is Honey Cream FAST version feminized.
I was planning to start flushing and harvesting in 2 weeks.
What should I do?
Thanks in advance.
Buds. Other
Other. Mold
3y ago
4
4
Solved
Eagers
Bud rot or normal?Hi guys does this looks normal for this stage mid-late flower? Lower leaves are starting to die off which looks normal but should leaves between buds be doing the same? I hope its not the start of budrot? Have fans on buds RH is 60-70% in greenhouse+dehumidifer+heater struggling.
Leaves. Dropping off
Leaves. Wilting
Other. Mold
5y ago
2
3
Solved
PREPPYPUNK
CAN I SALVAGE MY BROWN MOLD HARVEST WITH RESIN PRESS? OR DO YOU ABSOLUTLEY NEED TO GO WITH ALCOHOL?Help, Brown Mold on buds. Good amount. Hate to throw it away. Put it all in freezer after harvest and discovery of mold. IS SMOKING MOLDY WEED REALLY DANGEROUS? and Is there any other way to salvage besides using alcohol? Is it safe to press the resin out with resin press? Thanks
Buds. Other
Other. Mold
4y ago
4
3
Solved
BudMunchies
Remove Powdery Mildew on Clones?I have successfully cloned all 4 of my plants. However I also ended up with a powdery mildew problem. Or so i think thats what this is.
Are these clones ruined, or is there a good way for me to kill of the mildew without hurting the clones before i pot them in soil?
10mo ago
5
5
Solved
EXZELENS
Can I change my autoflowers light cycle withou reducing their yield significantly?I am having humidity/mold problems and was thinking of changing the cycle so the grow goes off at noon ( currently it goes off at 1am and its winter and gets real cold with 88% humidity).
Even if I stress them, it would be better to not have mold than reducing the yield, right?Other. Mold
Other. General questions
Setup. Lighting
5y ago
1
1
Solved
D7chow
Plants getting enough light?
Put a white greenhouse plastic over em that shades and diffuses the light. plants look happy with praying leaves . Or are they trying to stretch to much? Not exactly sure on the light transmission. Is lux a good way to test light in a greenhouse ?Week 10
Other. Mold
7y ago
1
1
Solved
Erasmus
Best way to control humidity?I have a 4 inch inline fan blowing in air at the bottom, I have a 4 inch inline fan sucking air out the top and a 4 inch fan to circulate air inside and a large 300 foot air dehumidifier in the tent but my humidity is still 50%-60% constantly. What am I doing wrong?Week 7
Other. Mold
5y ago
3
Solved
Dmesh
Should I defoliate during flowering outdoors?(Autoflower) Should I defoliate? I made the rookie mistake of doing NO defoliating or lst during vegging, cuz they were skinny then. Did minor defol during flowering.It’s in full flower with 2-3 weeks left and we have about 7 straight days of rain. Worried about wpm and bud rot.
2y ago
5
4
Solved
iopiopiop
WPM! Help!Soooo... today I found some quite heavy WPM between buds. Just a few sugar leaves were completely coated in white. So I lowered the rel. hum und sprayed the buds directly with h202. (non-diluted)
Will the plant survive untill harvest? Shouldnt I have not sprayed the buds directly
Week 12
Other. Mold
5y ago
1
2
Solved
JadamJatt
Infected Leaves. To remove part of the leaf or whole leaf?I had had pests and disease issues my second grow of Autoflowers. I believe it was hemp russet mites which spread disease on parts of many of my leaves. Would it be alright to remove only the part of the leaf that was infected or to remove the entire leaf?Leaves. Tips - Die
Other. Bugs
Other. Mold
3y ago
4
4
Solved
GenghiSkunk
The stem is pretty long (4-5 cm).
Is it normal for this strain?
Thanks,
M.Week 1
Other. Mold
6y ago
1
1